There is a tool to iron out burrs in a 22lr chamber that has been peened by the firing pin. I believe Brownell's should carry it. i have an old Remington 541-S that had been shot a lot. It did not have a firing pin spring like the later versions of that rifle.
Also, the 1992 edition of the old Gun Digest has a very good article about 22lr chambers that was written the former Tech Editor of American Rifleman, C. E. Harris. |
Last I heard only Tandemkross still sold those chamber "irons", at least that's what some folks on RFC had found.
https://www.tandemkross.com/ChamberM...erIroningSwage If you can't find one elsewhere they do have them. |
There's a guy at our club that has either Lapua or Ely make custom ammo for his rifle. IIRC, he buys 25,000 at a time. Just a WAG here but I assume his chamber is cut for this ammo. Your rifle may be in the same condition.
|
Chamber iron. Uses a chamber iron to fix the displaced metal from rimfire striker impact.
We had to build one at Gunsmith school. It irons the metal back in place. It doesn't cut out the displaced metal. Cutting with a reamer or file leaves a depression which can allow the rim to blow out, so the instructor said. Used it a lot on old guns, not so much on modern guns. |
Quote:
https://th.bing.com/th/id/OIP.FmHIbI...r=1.25&pid=1.7 https://th.bing.com/th/id/OIP.DkYlRR...r=1.25&pid=1.7 Could a nailset be made to work? Oil up the nailset and judiciously tap with a hammer or would that be nono? https://th.bing.com/th/id/OIP.NCuSYX...r=1.25&pid=1.7 Could probably find a way to spin a nailset. |
Quote:
-BCB |
You got lots of advise here, most of it bad.
This seems to be a match rifle, it should chamber any match ammo, specifically Lapua or ELEY. Before you screw with this gun, a few thoughts. I would guess, the camber is fouled badly, maybe some corrosion. First, clean the barrel with a good RF solvent and a bronze brush. When done get some C4 carbon cutter…often there is hard carbon/lead in the throat. Follow directions….only for throat. That may very well do it but as stated,check the radius of the chamber for a burr. P.S. Lapua & Eley do not make custom for anybody, including olympic teams. You might buy most of a given lot….but it is a production lot made to THEIR specs. I know a lot about these guns, have been shooting IR50/50 since 1980’s and sit way up in the gold HOF , winning state, regional, national champs. There’s lots of ways to screw up these guns. |
Quote:
Good Lord, people.......:eek::rolleyes: |
Quote:
-BCB |
Quote:
The amount of rifling engagement differs as these specialized chambers are done for specific ammo. That's where swapping ammo back and forth in chambers on real-deal 22LR target rifles can at times pose a problem. It's probable that there's nothing whatsoever 'wrong' with the chamber. Be aware that these target chambers may require the occasional use of a toothed little tool to remove the carbon and leading in the throat with "may" being the important word, here. Inspecting the chamber/throat with a borescope and identifying and correcting any cleaning-related issues is the first thing to do. If you have any questions, get the gun into the hands of someone that knows RF target chambers and builds these guns to help you out. These guns are specific and extremely specialized. Leave any nail setters, punches, hammers, trowels, etc. in the toolbox....:eek: This chart shows just a few of the different reamers that PTG has for specific ammo. There are many, many more variations! You can easily see the significant differences that can give issues when mixing different ammo and chambers: https://i.imgur.com/WuXL1YQl.jpg Good shootin' -Al |
All times are GMT. The time now is 09:20 AM. |
Powered by vBulletin® Version 3.8.1
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.