Saubier.com  



Go Back   Saubier.com > Search Forums

Showing results 1 to 25 of 34
Search took 0.01 seconds.
Search: Posts Made By: luke wady
Forum: Bullet Making 09-24-2014, 04:23 PM
Replies: 26
Views: 5,992
Posted By luke wady
thanks for all the info

Hi Lads
A big thanks for all the info and i don't think ill be getting in jacketed bullet making just yet , I managed to find a few box's of 30gr bergers that i have been using,

luke
Forum: Small Caliber Discussion Board 09-24-2014, 04:19 PM
Replies: 11
Views: 1,715
Posted By luke wady
it could be done

hi
you will need to open up bolt face and it can be cut with a small carbide boring bar.
luke
Forum: Bullet Making 09-12-2014, 07:58 PM
Replies: 26
Views: 5,992
Posted By luke wady
set up cost

Hi George
Could you please advise me on what would be needed if I was to start making my own bullets in .17 cal
thanks luke
Forum: Bullet Making 09-12-2014, 03:47 PM
Replies: 26
Views: 5,992
Posted By luke wady
Hot core ?

hi George Ulrich
thanks for the info can see the spring back in jacket and core differ, as lead as a lot lower melting point than gilding metals annealing point , but it all sounding like a lot of...
Forum: Bullet Making 09-11-2014, 08:50 PM
Replies: 26
Views: 5,992
Posted By luke wady
Smile thanks again

hi Lads
well i think this weekend ill have a go at making myself a draw die set , i have nothing to loss but bit of time,
.204 less .172 is .032 so i figger ill try on one go and see if it...
Forum: Bullet Making 09-08-2014, 06:52 AM
Replies: 26
Views: 5,992
Posted By luke wady
Thanks for the info

Hi Lad's
thanks for the info . Going to have get a draw die then .
Thanks luke
Forum: Bullet Making 09-07-2014, 02:15 PM
Replies: 26
Views: 5,992
Posted By luke wady
.20 cal to 17 cal will it work ?

hi
i am think of sizing .20 cal to .17 cal
as i can no longer get any 30gr .17 here in uk
as any one tried this and what do i need ?

thanks
luke
Forum: Small Caliber Discussion Board 04-27-2014, 06:34 PM
Replies: 18
Views: 2,891
Posted By luke wady
mag bodys

hi.
just mill it out to fit , you need the re-cut the ramp too. but that easy to, jut don't cut any off the abutment height,
hope this makes it easier,
my .17fb is on 222 action ,

222,...
Forum: Project Guns 04-07-2012, 10:02 PM
Replies: 8
Views: 16,111
Posted By luke wady
that springy plate

i work o a few of this and have found a dab of super glue to hold it to the action dose no harm:)
Forum: Small Caliber Discussion Board 12-15-2011, 08:45 PM
Replies: 67
Views: 11,265
Posted By luke wady
brass

i hope they get there act together on brass , the only bag i got was that bad i have been making my owen form .223 a real mess around
Forum: Small Caliber Load Data 11-24-2011, 08:46 PM
Replies: 5
Views: 1,939
Posted By luke wady
not goning to try it

hi lads
i use lil gun in my 22hornet 10.3 gr and 45 gr hornady bee bullets

so i have the powder a round and saw the same question on a from in here in enland so i throught id ask it here as
we...
Forum: Small Caliber Load Data 11-21-2011, 10:41 PM
Replies: 5
Views: 1,939
Posted By luke wady
thanks lads

hi all
thanks for that ,its just as throught ,
:(
Forum: Small Caliber Load Data 11-20-2011, 08:08 PM
Replies: 5
Views: 1,939
Posted By luke wady
lil gun in .17 fb or mach4

hi
i have seen the question asked on a uk from,
i think lil gun would be to fast to get the best out of .17 fb.
i would like to hear if any one as tried it? and what resultes they got ?
thanks...
Forum: Small Caliber Load Data 10-31-2011, 07:43 PM
Replies: 23
Views: 5,606
Posted By luke wady
thanks for that Ab :)

thanks for that Ab :)
Forum: Small Caliber Load Data 10-30-2011, 10:40 PM
Replies: 23
Views: 5,606
Posted By luke wady
here link for pics

http://s1182.photobucket.com/albums/x453/lukewady/
Forum: Small Caliber Load Data 10-30-2011, 10:30 PM
Replies: 23
Views: 5,606
Posted By luke wady
hi lads heres my progerss, made a bushing die...

hi lads
heres my progerss, made a bushing die out of a lee .221 fb die, then made 3 bushings , sized at .280 .250 .220 ,ran case through them , and then through my .17 full lengh die
...
Forum: Small Caliber Load Data 10-26-2011, 06:01 PM
Replies: 23
Views: 5,606
Posted By luke wady
ill do that this week end when i have made a few...

ill do that this week end when i have made a few case's :)
Forum: Small Caliber Load Data 10-25-2011, 09:55 PM
Replies: 23
Views: 5,606
Posted By luke wady
Smile made frist case today

hi finished making my die ,
i have bored out a lee full lenght .221 die to take bushings
,i had set should back with it as standerd but this made creases in shoulder
so bore it out and have made...
Forum: Small Caliber Load Data 10-19-2011, 08:45 PM
Replies: 17
Views: 5,208
Posted By luke wady
h322

i have only just started playing with my 17fb , but had some h322 from when i had 223 , and i have found that 17.5gr is working well with the 30gr bergers

going to tring 25 vmax soon as i make...
Forum: Small Caliber Load Data 10-16-2011, 06:45 PM
Replies: 23
Views: 5,606
Posted By luke wady
just getting all the bit together , looking...

just getting all the bit together , looking forward to doing it as th brass i can gat is not any good found 2 case with spilt neck's 1 with undersize rim and 8 with poorly formed shoulders

and...
Forum: Small Caliber Load Data 09-26-2011, 09:37 PM
Replies: 23
Views: 5,606
Posted By luke wady
so it lool like less sizeing than i was thinking....

so it lool like less sizeing than i was thinking.

i think i only need one intermedate from 223 to .221
then
one between 221 and .17, ill keep you al posted

thanks luke
Forum: Small Caliber Load Data 09-25-2011, 08:48 PM
Replies: 23
Views: 5,606
Posted By luke wady
iam going to make my owen as i run my owen...

iam going to make my owen as i run my owen machine shop. how meny steps do they use?

thanks
Forum: Small Caliber Load Data 09-25-2011, 07:57 PM
Replies: 23
Views: 5,606
Posted By luke wady
.17 fire ball case from .223

hi
iam going to make my owen case's
how meny forming die do i need to make ,

i was thinkin ill need to go to 7mm then 6.5 them 6 mm the a .221 fire ball die
the neck to .20 cal then full...
Forum: Project Guns 08-20-2011, 02:57 PM
Replies: 3
Views: 2,111
Posted By luke wady
rota mod

if you are going to rimmless case you could just remove all but the first vain,on the rota, some steyr mag work like this, the older .222 /.223
Forum: Small Caliber Load Data 08-04-2011, 10:40 PM
Replies: 14
Views: 3,492
Posted By luke wady
dean in England 100 fire ball case are 59 for...

dean
in England 100 fire ball case are 59 for r- P lapua .223 match is 59

they both imports to us
Showing results 1 to 25 of 34

 
Forum Jump

All times are GMT. The time now is 12:46 PM.


Powered by vBulletin® Version 3.8.1
Copyright ©2000 - 2019, Jelsoft Enterprises Ltd.