Forum: Classifieds
06-03-2020, 12:47 PM
|
Replies: 0
Views: 1,638
WTB 5mm Remington Magnum rimfire finish reamer
I'm trying to locate a finish reamer for the old Remington 5mm magnum rimfire. Need to cut a barrel back and rechamber due to pitting ahead of the original chamber and the only place I can find a...
|
Forum: Small Caliber Discussion Board
02-11-2020, 05:53 PM
|
Replies: 11
Views: 5,578
I sent a request directly to Hodgdon asking if...
I sent a request directly to Hodgdon asking if they could give me the PSI of the 22 Hornet as listed on their web site using Lil' Gun powder which they only show in CUP. I never got a reply but I...
|
Forum: Small Caliber Discussion Board
02-06-2020, 12:46 PM
|
Replies: 11
Views: 5,578
|
Forum: Small Caliber Discussion Board
02-05-2020, 10:28 PM
|
Replies: 11
Views: 5,578
I found a site that says there is a correlation...
I found a site that says there is a correlation between CUP an PSI and even has a formula to convert CUP to PSI. It takes the CUP value and multiplies it by 1.156 and then subtracts 17902.0 and gives...
|
Forum: Small Caliber Discussion Board
02-05-2020, 05:50 PM
|
Replies: 11
Views: 5,578
Is there a way to cross reference CUP to PSI?
I know they are measured differently but wondered if there was a way to get a good estimate of CUP in PSI. I was checking Hodgdon for reloading the 22 Hornet and two powders they show pressure in...
|
Forum: Small Caliber Discussion Board
02-05-2020, 05:38 PM
|
Replies: 6
Views: 2,484
I got a reply back on January 28th from John....
I got a reply back on January 28th from John. This was his report shown below. By the way, John is really into the 5mm Remington magnum rimfire.
"Hoping to get away next week mate and have some...
|
Forum: Small Caliber Discussion Board
02-04-2020, 10:54 PM
|
Replies: 44
Views: 14,952
|
Forum: Small Caliber Discussion Board
02-04-2020, 03:48 PM
|
Replies: 44
Views: 14,952
squirrel_slayer,
I don't know if this would...
squirrel_slayer,
I don't know if this would help at all but the factory 22 TCM brass is a bit thinner in the case sides and might allow a bit more volume and require less reaming when you form it to...
|
Forum: Small Caliber Discussion Board
02-03-2020, 03:29 PM
|
Replies: 44
Views: 14,952
I'm late into this thread but ran into the same...
I'm late into this thread but ran into the same problem years ago with my own special cartridges. If you are looking for short commercial bullets Barnes makes a 30gr varmint Grenade flat base that's...
|
Forum: Small Caliber Discussion Board
10-16-2019, 05:23 PM
|
Replies: 8
Views: 4,190
|
Forum: Small Caliber Discussion Board
10-15-2019, 05:05 PM
|
Replies: 8
Views: 4,190
You didn't change the stock to one of those...
You didn't change the stock to one of those aluminum chassis? If and when I get one I want it bone stock. Can't see buying a rifle and spending near the same amount on replacing the factory stock. I...
|
Forum: Small Caliber Discussion Board
10-15-2019, 01:28 PM
|
Replies: 8
Views: 4,190
Ruger American Predator in 6.5 Grendel?
I know the caliber is a bit large for here but I actually was more interested in the rifle. I shoot that round in an AR and since I'm old a decrepit I hate to have to hunt for the brass so I'd like...
|
Forum: Small Caliber Discussion Board
08-27-2019, 12:11 PM
|
Replies: 6
Views: 4,452
|
Forum: Small Caliber Discussion Board
08-26-2019, 04:34 PM
|
Replies: 6
Views: 4,452
|
Forum: Small Caliber Discussion Board
08-26-2019, 12:38 PM
|
Replies: 6
Views: 4,452
20 caliber version of the 17 VHA?
I was wondering if anybody had done a 20 caliber version of the 17 VHA or just necked up the 4.6X30 Cartridge or the 5.7X28 cartridge? I've had less luck with the 5.7X28 brass I've bought on line...
|
Forum: Small Caliber Discussion Board
08-06-2019, 01:44 PM
|
Replies: 13
Views: 6,236
|
Forum: Small Caliber Discussion Board
08-05-2019, 01:55 PM
|
Replies: 13
Views: 6,236
|
Forum: Small Caliber Discussion Board
07-20-2019, 01:03 PM
|
Replies: 4
Views: 2,616
This is a picture of the 17 Reed express on the...
This is a picture of the 17 Reed express on the left with a 22 Reed express on the right. I'm not sure but I don't think it would lend itself well to a Martini type action since it is rimless. The 17...
|
Forum: Small Caliber Discussion Board
07-12-2019, 04:51 PM
|
Replies: 7
Views: 3,782
|
Forum: Small Caliber Discussion Board
07-10-2019, 08:53 PM
|
Replies: 27
Views: 11,479
|
Forum: Small Caliber Discussion Board
07-10-2019, 12:31 PM
|
Replies: 27
Views: 11,479
|
Forum: Small Caliber Discussion Board
07-08-2019, 01:19 PM
|
Replies: 27
Views: 11,479
I may have to check into it since I'm thinking...
I may have to check into it since I'm thinking about a liner. I got a 17HMR reamer from Manson years ago that said on it for Redman linner. That rifle shoots really good. Building up a nice Mossberg...
|
Forum: Small Caliber Discussion Board
07-08-2019, 01:00 PM
|
Replies: 12
Views: 4,837
|
Forum: Small Caliber Discussion Board
07-06-2019, 03:13 PM
|
Replies: 12
Views: 4,837
|
Forum: Small Caliber Discussion Board
06-30-2019, 07:36 PM
|
Replies: 27
Views: 11,479
|