Saubier.com  



Go Back   Saubier.com > Search Forums

Showing results 1 to 21 of 21
Search took 0.02 seconds.
Search: Posts Made By: sagerat
Forum: Classifieds 07-04-2017, 05:41 PM
Replies: 3
Views: 2,616
Posted By sagerat
I have just what you are looking for- 5x35 SMc...

I have just what you are looking for- 5x35 SMc reamer and go/ no-go gauges.
Just wanting to rent at this time as I may do another barrel at some point.
Send me a PM if interested.
James
Forum: Classifieds 03-08-2014, 11:12 PM
Replies: 6
Views: 2,786
Posted By sagerat
How about a 6x47 based on the 222 mag case- any...

How about a 6x47 based on the 222 mag case- any interest? The one I built shooting 58 gr V-Max has been pretty hard on the coyotes. I have a reamer and headspace gauges available.
James
Forum: Small Caliber Discussion Board 09-26-2013, 02:20 PM
Replies: 4
Views: 3,525
Posted By sagerat
Thanks for the info- I have a VarTarg reamer...

Thanks for the info- I have a VarTarg reamer ordered.
James
Forum: Small Caliber Discussion Board 09-21-2013, 03:43 AM
Replies: 4
Views: 3,525
Posted By sagerat
20 VT chamber

Hi all- this may be a stupid question, but can a 20 VarTarg chamber be made with a .204 Ruger reamer run in short. It looks like a 20 VT neck is longer than a .204 Ruger, but I don't know this for...
Forum: Small Caliber Discussion Board 09-04-2013, 02:45 AM
Replies: 8
Views: 5,207
Posted By sagerat
From what I have read and experienced, the small...

From what I have read and experienced, the small rifle primers give an edge on accuracy. I have yet to have any failure to fire in 20- 90 degree weather with the small primers. I have been very...
Forum: Small Caliber Discussion Board 09-01-2013, 09:15 PM
Replies: 8
Views: 5,207
Posted By sagerat
I have been using 41.0 gr. of IMR 4064 in my 22...

I have been using 41.0 gr. of IMR 4064 in my 22 CHeetah MK1 with a 52 gr. HP and CCI 450 primer for fire forming. This is with Lapua Palma brass with the small primer pocket and a 1-14 twist barrel....
Forum: Bullet Making 06-11-2013, 04:45 AM
Replies: 25
Views: 14,344
Posted By sagerat
TinMan- wouldn't an unleaded bullet still be...

TinMan- wouldn't an unleaded bullet still be swaged in a conventional jacket, just using a different core- like you say sintered.
Forum: Bullet Making 06-07-2013, 05:56 AM
Replies: 25
Views: 14,344
Posted By sagerat
Does anyone swage unleaded? James

Does anyone swage unleaded?

James
Forum: Classifieds 05-15-2013, 02:21 PM
Replies: 5
Views: 2,871
Posted By sagerat
I'll take these- just PM payment info James

I'll take these- just PM payment info
James
Forum: Classifieds 04-30-2013, 01:46 AM
Replies: 4
Views: 2,765
Posted By sagerat
Aussiebluey- enjoy the reading. Someone else...

Aussiebluey- enjoy the reading. Someone else offered up a set, so I will have some too.
Forum: Classifieds 04-27-2013, 03:27 PM
Replies: 4
Views: 2,765
Posted By sagerat
I'll take these if they aren't going to the...

I'll take these if they aren't going to the Aussie land.

James
Forum: Small Caliber Discussion Board 04-15-2013, 02:32 PM
Replies: 27
Views: 6,948
Posted By sagerat
headspace

There are some other measurements that should be taken- how much clearance is there between the bolt nose and barrel. Also, how much clearance is there between the front of the bolt lugs and barrel....
Forum: Small Caliber Discussion Board 04-14-2013, 09:48 PM
Replies: 5
Views: 2,209
Posted By sagerat
It might be possible to use a thicker recoil lug...

It might be possible to use a thicker recoil lug and avoid buying a reamer.

James
Forum: Classifieds 03-26-2013, 01:45 AM
Replies: 2
Views: 2,490
Posted By sagerat
I'll take the whole lot- $170 TYD Thanks

I'll take the whole lot- $170 TYD
Thanks
Forum: Classifieds 02-12-2013, 01:21 AM
Replies: 17
Views: 4,561
Posted By sagerat
sounds good to me also, I'll send a PM with more...

sounds good to me also, I'll send a PM with more info
Forum: Classifieds 02-12-2013, 12:07 AM
Replies: 17
Views: 4,561
Posted By sagerat
I would be interested in #67-84 James

I would be interested in #67-84
James
Forum: Classifieds 12-09-2012, 01:15 AM
Replies: 2
Views: 2,073
Posted By sagerat
I have one on a Rem. 722 that I have been meaning...

I have one on a Rem. 722 that I have been meaning to pull off if that would interest you.
Forum: Classifieds 08-18-2012, 03:03 PM
Replies: 7
Views: 3,403
Posted By sagerat
I'll take it if it is still available- just PM...

I'll take it if it is still available- just PM payment details
Forum: Classifieds 05-29-2012, 05:33 PM
Replies: 7
Views: 2,774
Posted By sagerat
22br

I have a new set of Forster 22 BR dies - this is the 2 die neck sizing set- non bushing. I'd let these go for 45 plus shipping.
James
Forum: Classifieds 11-02-2011, 02:12 AM
Replies: 2
Views: 2,691
Posted By sagerat
I'll take this trigger if still available. Please...

I'll take this trigger if still available. Please PM payment details
Forum: Classifieds 06-27-2011, 03:51 AM
Replies: 7
Views: 2,932
Posted By sagerat
I'll take the rest, both the 204 and the 224 ...

I'll take the rest, both the 204 and the 224

James
Showing results 1 to 21 of 21

 
Forum Jump

All times are GMT. The time now is 01:44 PM.


Powered by vBulletin® Version 3.8.1
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.