Forum: Small Caliber Discussion Board
07-29-2016, 07:41 PM
|
Replies: 2
Views: 2,540
|
Forum: Small Caliber Discussion Board
07-27-2016, 10:56 PM
|
Replies: 1
Views: 2,036
forming 17-223 brass
Trying to figure out what I need to form17x223 brass Then later resize and seat bullets.
The dies I have now that may work are Redding type s dies in the following calibers;
6mm-223
17 Remington...
|
Forum: Small Caliber Discussion Board
07-26-2016, 12:45 PM
|
Replies: 2
Views: 2,540
Norma 17 Remington Brass
Is the Outside diameter of a loaded round with Norma brass the same size as the Remington brand for the 17 Remington? My loaded brass with the Remington brand measures .1925 to .1930
thanks
...
|
Forum: Small Caliber Discussion Board
09-11-2008, 10:51 PM
|
Replies: 15
Views: 5,280
|
Forum: Small Caliber Discussion Board
09-10-2008, 11:58 PM
|
Replies: 15
Views: 5,280
GLWenzl
I went back and remeasured the...
GLWenzl
I went back and remeasured the loaded case, the measurement was taken on the upper third case neck as I did not resize the entire neck, it measured .197 with my set of Sinclair calipers. ...
|
Forum: Small Caliber Discussion Board
09-10-2008, 09:21 PM
|
Replies: 15
Views: 5,280
|
Forum: Small Caliber Discussion Board
09-09-2008, 09:38 PM
|
Replies: 15
Views: 5,280
|
Forum: Small Caliber Discussion Board
09-09-2008, 04:49 PM
|
Replies: 15
Views: 5,280
17 Mach iv HELP
My 17 encore is not shooting well at all. I noticed after firing, i could not insert a bullet into the fired case neck on about 70% of all the cases fired.
This made me wonder if the case necks...
|
Forum: Small Caliber Discussion Board
01-14-2007, 11:09 PM
|
Replies: 1
Views: 2,483
IMR 3031 Or WW748
Has anyone tried 3031 or 748 or Varget in the 17 Mach iv in either 25 or 30 grain bullets. I have several pound of 748 that I would like to use??
thanks
|
Forum: Small Caliber Discussion Board
01-07-2007, 01:21 PM
|
Replies: 7
Views: 3,131
ditto on clarity in the upper range, I have a...
ditto on clarity in the upper range, I have a 3x12 I've been playing with for about 3 months and from 9 power to 12 the light gathering is minimal and the focus clarity problems. I'm sending mine...
|
Forum: Small Caliber Discussion Board
11-21-2006, 12:19 AM
|
Replies: 4
Views: 12,944
|
Forum: Small Caliber Discussion Board
11-07-2006, 11:56 PM
|
Replies: 11
Views: 6,257
Try Mike Bellm in Oregon, lots of really good...
Try Mike Bellm in Oregon, lots of really good stuff on his web sites. I used some of his 2x hinge pins in my gun and was very surprised to watch the group size shrink with every load tested. This...
|
Forum: Small Caliber Discussion Board
11-03-2006, 05:40 PM
|
Replies: 3
Views: 4,325
204 brass to 17 rem
I read somewhere recently that 204 brass can be passed thru a 17rem full length die and presto instant 17 rem. Is it really that easy, same shoulder angle, no triming, ect?
Tcas
|
Forum: Small Caliber Discussion Board
10-29-2006, 11:12 PM
|
Replies: 7
Views: 4,096
|
Forum: Small Caliber Discussion Board
10-20-2006, 06:10 PM
|
Replies: 4
Views: 4,344
|
Forum: Small Caliber Discussion Board
10-20-2006, 11:59 AM
|
Replies: 4
Views: 4,344
|
Forum: Classifieds
10-15-2006, 11:14 PM
|
Replies: 2
Views: 4,387
|
Forum: Small Caliber Discussion Board
10-13-2006, 04:12 PM
|
Replies: 6
Views: 5,888
|
Forum: Small Caliber Discussion Board
10-12-2006, 04:07 PM
|
Replies: 15
Views: 8,618
|
Forum: Classifieds
10-06-2006, 01:10 AM
|
Replies: 2
Views: 4,387
encore 17 Mach iv VanHorn barrel
I have an encore 17 Mach iv VanHorn barrel 24inch 1/9 twist with beaver tail forend. I'm considering selling for about $350. I will take a pic and try to post on Friday. Barrel shoots great but I...
|
Forum: Small Caliber Discussion Board
09-30-2006, 01:50 AM
|
Replies: 10
Views: 7,474
Dan,
that is interesting, the only reason I...
Dan,
that is interesting, the only reason I considered Lil gun was because I noticed that many of the powders used in 223 rem were also used in the 17 remington with a few grain less powder, so I...
|
Forum: Small Caliber Discussion Board
09-29-2006, 01:35 PM
|
Replies: 10
Views: 7,474
Jim,
I have only used 10x 16.5 grains with...
Jim,
I have only used 10x 16.5 grains with small rifle CCI BR, 25 grain berger, it was shooting about 1inch at 175 yards from my tailgate. The primers go a little flat with 16.5 grains I tried 17...
|
Forum: Small Caliber Discussion Board
09-28-2006, 12:55 AM
|
Replies: 10
Views: 7,474
cz rebarrel to 17 mach iv
I finally decided to take the plunge and order another CZ 221 fireball but have it rebarreled to 17 mach iv. I have seen several posters on this board live in the Delmarva area. I'm about 1/2 hour...
|
Forum: Small Caliber Discussion Board
09-27-2006, 12:40 AM
|
Replies: 2
Views: 4,656
|