Saubier.com  



Go Back   Saubier.com > Saubier.com Forums > Small Caliber Discussion Board

Reply
 
Thread Tools Display Modes
  #1  
Old 01-29-2020, 01:11 PM
JonathanL JonathanL is offline
Member
 
Join Date: Oct 2006
Location: England. North East Coast
Posts: 30
Default Current .14 barrel makers

Long time since I've posted here - six years since I logged in, apparently!

What's the current status with .14 cal barrel supplies - specifically blanks? Who makes them? I think Pac-Nor may have done them as a special order but I've just read about their factory burning down

When I got my .14 Walker built years back I got a reamer to cut a .14-222 chamber at the same time along with about 300 pieces of brass made by a member here. I'd be looking at maybe something 24" or 26" in length.

The other complication is that I'm in the UK and it's a nightmare getting anything remotely firearms related out of the US without expensive licensing.

I'm going to order a set of bullet swaging dies from Corbin so I may as well have the other rifle made to justify the cost of the dies a bit more.

Any help appreciated.
Reply With Quote
  #2  
Old 01-30-2020, 02:19 AM
L.Sherm L.Sherm is offline
Senior Member
 
Join Date: Feb 2014
Location: Havre, Montana
Posts: 692
Default

Shoot Jingweed on here a p.m he was looking for a 14 cal. barrel a few months ago, dont know if he found one though he may have a lead on one.
Reply With Quote
  #3  
Old 01-30-2020, 01:32 PM
DAVID DAVID is offline
Senior Member
 
Join Date: Nov 2012
Posts: 263
Default

Back in the early 90's, I made 100 barrel blanks in .14 caliber and it took a little over 3 years to sell them.

I chambered around 20 of them for my ".14 Piss Ant" cartridge, which was the .25 acp. necked down to .14 caliber.

Other guys that bought the remaining barrel blanks, we're necking down the 22 Hornet, as well as shortened and modified versions of the Hornet case, all necked down to .14 caliber.

And as a matter of fact, I talked to an elderly gentleman in Casper Wyoming back around the first part of December, and to this day, he is still shooting one of my original custom Contender barrels in .14 Piss Ant! This was the first time I heard anyone mention anything about this in over a quarter of a century! It just made my day!

I don't remember the name as it has been many years now, but there was a small barrel company that specialized in .10, .12 and .14 caliber barrels, as barrel blanks and chambered barrels. I'll do some checking around and see if I can get lucky and find some useful information on this.
Reply With Quote
  #4  
Old 01-30-2020, 02:29 PM
ray h ray h is offline
Supporting Member
 
Join Date: Jun 2007
Location: central Md
Posts: 2,854
Default

Wasn't it Lawrence that made those barrels?
Reply With Quote
  #5  
Old 01-30-2020, 03:35 PM
DAA DAA is offline
Senior Member
 
Join Date: Oct 2006
Location: West Bountiful, Utah
Posts: 787
Default

I know when my old friend Blaine was playing with 14s he was using Jeff Lawrence barrels but Proof Research bought him out years ago and I've no idea what current status is.

- DAA
Reply With Quote
  #6  
Old 02-12-2020, 08:11 PM
JohnW...ski JohnW...ski is offline
Junior Member
 
Join Date: Nov 2016
Posts: 16
Default .14 Bullets

On another note, anyone have any good sources for .14 caliber bullets?
John
Reply With Quote
  #7  
Old 02-13-2020, 12:32 PM
Tparrish Tparrish is offline
Supporting Member
 
Join Date: Feb 2007
Location: Leavenworth Kansas
Posts: 536
Default

Try Reed Ammunition & research, he is a sponsor here.

Tom
Reply With Quote
  #8  
Old 03-06-2020, 07:33 PM
JohnW...ski JohnW...ski is offline
Junior Member
 
Join Date: Nov 2016
Posts: 16
Default

Quote:
Originally Posted by Tparrish View Post
Try Reed Ammunition & research, he is a sponsor here.

Tom
I have had poor luck with his crappy bullets.
Thanks anyway,
John
Reply With Quote
  #9  
Old 03-10-2020, 03:38 PM
The Old Redneck The Old Redneck is offline
Senior Member
 
Join Date: Oct 2006
Location: Alabama
Posts: 289
Default Reed bullets

Tparrish, I have had excellent results with Reeds bullets and everything else I bought from him over the years. Own and have owned several 14's. Would rather buy his than make them myself. Lot less work. The 14's can be a pain to clean. I shot moly for years and still do in some barrels. All barrels in the 14's require cleaning to keep accuracy. Bare copper in some barrels with some loads fouls quickly and accuracy goes with it. Removing copper and fouling in the tiny barrels takes work. Also as the throat grows some barrels lose accuracy quickly. Having multiple 14's if accuracy drops on one and same bullets still shoot in another I dont blame the bullets. I start working on the barrel. After soaking one in a 50/50 mix of acetone and auto transmission fluid for a week and scrubbing good accuracy usually returns if throat and crown is good. Setting barrel back has been required. I have both .142 and .144 barrels in twist running from 1 in 10 to 1 in 6. Shoot the same .144 bullets in all. Stopped shooting turned bullets a few years ago and just shoot jacketed. Nothing wrong with turned just stopped making them when I stopped turning .10 and .12 calibers. I consider Reed a friend, he has always been first class in our business dealings. His products always as advertised. He has actively worked to keep the subcalibers under .17 alive after Mr. Bill Eichelberger passed. Definitely not a money making situation. It takes 7 pulls on a bullet press handle to make each .14 caliber bullet. Making jacket cups, cores, seating and pointing. I have the presses, and dies, have and do make bullets for my own use. At 700 pulls to form jacket cups, cores, seat cores, point and finish bullet, not counting time to lube and remove lube, polish etc for each 100 bullets. Not to mention cutting lead wire and everything involved in making cores. Go to the expense of buying dies, press, 17 caliber jacket cups to make the 14 jacket cups. The lead wire for the cores. Then spend hours turning it into 100 bullets for someone else to shoot. I wouldn't make 14 caliber bullets to sell if they brought $10 per bullet. My time is worth more than that to me. Rest assured if I make bullets now they are something I cant buy. A open forum is not the place to bad mouth anyone. Nobody will ever please everyone. Also a slightly over size bullet is usually more accurate, not less. I apologize for the rant.
Reply With Quote
  #10  
Old 03-10-2020, 04:06 PM
Tparrish Tparrish is offline
Supporting Member
 
Join Date: Feb 2007
Location: Leavenworth Kansas
Posts: 536
Default

The Old Redneck. FYI if you thought I was bad mouthing Mr Reed or his products I wasn't. I simply referred Mr Reed as a supplier for 14 Cal stuff.

Tom
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT. The time now is 05:06 PM.


Powered by vBulletin® Version 3.8.1
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.